Here is how to sight in a rifle without burning a box of ammo: bore sight it at home, get on paper at 25 yards, then do the real zero at 100. Done right, it takes about 20 rounds and an hour at the range. The steps are the same for a scope, a red dot or a lever gun with a peep sight.

What you need to sight in a rifle
- The rifle, with the scope mounted and the ring screws tightened to the maker’s spec.
- A bore sighter if you can’t look through the barrel. The Sun Optics 18-piece bore sight kit is $58.99.
- A solid rest: sandbags, a rest, or a bipod like the Magpul M-LOK bipod ($185.99).
- Targets with a 1 inch grid, so you can count how far off you are.
- At least 20 rounds of the exact ammo you will hunt with.
- Ear and eye protection. Electronic earbuds like the Axil XCOR ($198.99) let you hear range commands between shots.
Step 1: mount the scope properly
Set the eye relief so you see a full picture without craning your neck, level the reticle with the rifle, and tighten the rings evenly to the torque the maker lists. A scope that shifts in its rings will never hold a zero, and no amount of clicking fixes it. 1 inch scopes need 1 inch rings, like the Nikko Stirling 1 inch Weaver-style mount at $15.88.
Step 2: bore sight the rifle at home
With a bolt action, take the bolt out, rest the rifle so it can’t move, and look through the barrel at something 25 metres or more away. Centre that object in the bore, then adjust the scope until the crosshair sits on the same spot without moving the rifle.
Lever, pump and semi-auto rifles don’t let you look down the bore, so use a bore sighter. The Sun Optics kit is a collimator: pick the stud that fits your bore, fit it to the muzzle, look through the scope at the grid, and dial the crosshair onto its centre. Either way, a bore sight puts the rifle on paper. It is not a zero.
Step 3: first shots at 25 yards
Fire three careful shots at the centre of the target. Find the middle of the group, measure how far it is from where you aimed, and adjust. The turret arrows show which way the bullet will move, so turn elevation toward “Up” if the group is low and windage toward “R” if it is left.
The click maths: most hunting scopes move 1/4 MOA per click, which is about 1/4 inch at 100 yards. At 25 yards each click moves only about 1/16 inch, so you need four times as many clicks. A group 1 inch low at 25 yards needs about 16 clicks up. If your scope reads in MRAD, each 0.1 mil click is 1 cm at 100 metres and 2.5 mm at 25.
Step 4: the real zero at 100 yards
Move to 100 yards, or 100 metres if that is what your range has. The difference is about 9 percent and won’t matter for this. Shoot three-shot groups, adjust, and let the barrel cool between groups, since a hot barrel can move the point of impact.
Where to zero depends on the rifle:
- Flat-shooting deer calibres like .308, .270, .30-06 and 6.5 Creedmoor: many hunters zero 2 to 3 inches high at 100 yards, which keeps them close to dead on out to about 200 to 250 yards.
- Lever guns in .357, .44 or .45-70, and slug guns: zero at 50 to 100 yards and keep your shots inside that.
- .22 LR: 50 yards is a common zero.
Step 5: confirm with your hunting ammo
Different bullets and loads hit in different places, so finish with the exact load you will hunt with, like Federal ELD-X .308 178 grain ($58.88) or Sellier & Bellot 6.5 Creedmoor 140 grain soft point ($31.99). Before the season, check it again with one shot from a cold barrel, since that first shot is the one that counts in the field. Sight the rifle in again any time it takes a hard knock or travels a long way.
How to sight in a rifle with iron sights or a red dot
Iron sights follow one rule: move the rear sight the way you want the bullet to go, and the front sight the opposite way. Make small moves and shoot again. A red dot works like a scope, but the click values are often different, so check the manual. On a lever gun or shotgun, zero a red dot at 50 yards.
When the rifle won’t group
- Groups wander: check the ring and base screws first, then your rest.
- Shots climb as you go: the barrel is heating up. Slow down.
- Big, round groups: try another load. Some rifles just don’t like certain ammo.
- The scope runs out of adjustment: the bases or rings may be off. Have a gunsmith look.
A scope that suits the rifle makes all of this easier. Our best scope for deer hunting guide covers what to buy, and Wikipedia’s page on telescopic sights explains how they work.
Prices current as of October 2026. Check each product page for live stock.