Hunting, Information & Education, Outdoors

How to Keep Guns From Rusting in a Safe (Canadian Guide)

Silent Dry Hypercube gun safe dehumidifier, anti-rust, for a 150L safe

A locked safe keeps a gun from being stolen. It does nothing to keep it from rusting. Steel, moisture and a few weeks of neglect are all it takes, and a closed steel box in a Canadian basement is about the best rust incubator you could design. This is a short guide on how to keep guns from rusting in a safe: why it happens, and the cheap fixes that stop it.

Why guns rust inside a safe

Rust needs two things: bare steel and water. The water comes from the air. Once the humidity inside the safe sits above roughly 50 percent, a thin film of moisture forms on metal and the bluing starts to spot. You will not see it happen. You open the safe in the spring and there it is.

A few things make it worse in Canada:

  • Basements. Most safes live there, and most basements run 60 to 70 percent humidity from spring to fall.
  • Cold guns coming inside. A rifle that spent the day at minus ten sweats the moment it hits warm indoor air. Put it straight in the safe and you have sealed that condensation in with it.
  • Fire-rated safes. The fireboard lining that earns the rating is gypsum, and gypsum holds moisture. A brand new fireproof safe can run damper than the room around it.
  • Stripped surplus rifles. If you just cleaned the cosmoline off an SKS, you removed the only thing that kept it rust-free for 60 years. It is bare steel now.

Step 1: Find out what your safe is actually doing

Guessing does not work. Put a hygrometer in the safe and check it after a couple of days with the door shut. You want 30 to 50 percent. Under 30 is unnecessary and can dry out wood stocks. Over 50, keep reading.

The Silent Dry Hypercube has a hygrometer built into the face, so you get the reading every time you open the door without buying a separate gauge.

Silent Dry Hypercube dehumidifier, used to keep guns from rusting in a safe
Hypercube dehumidifier. The dial on the front is the hygrometer.

Step 2: Pull the moisture out of the air

You have three realistic options.

Electric dehumidifier rod

Works well, but you need to drill a hole in the safe for the cord and have an outlet nearby. That rules out a lot of basement corners and every cabinet at the cottage.

Renewable desiccant

A block of silica-type material that soaks up moisture until it is full, then gets dried out and reused. No cord, no hole, no batteries. The Hypercube is this type. When the hygrometer says it is saturated, you microwave it and put it back. It is the Silent Dry product we sell the most of, because it works in any safe, cabinet or case.

Sizing is simple. Small for a cabinet or a few long guns, Medium for a typical 20 to 30 gun safe, Large for a big safe or a damp basement where you want extra margin. For a pistol case or an ammo can, the Invisible Dehumidifier Stone is the same material in a pocket-sized block.

Throwaway silica packets

The little packets that come in shoeboxes. Fine for a hard case on a road trip. Not enough capacity for a safe, and you cannot tell when they are spent.

Step 3: Protect the steel directly

Drying the air handles most of the problem. For the last bit, and for the guns you care about most, put something on or around the metal itself.

VCI (vapour corrosion inhibitor) is the same thing the military packs spare parts in. A small emitter gives off a molecule that settles on nearby metal as an invisible layer, and that layer keeps water and oxygen off the surface. It is odourless, leaves no residue and does not bother optics or ammo.

The VaporTack SilentDry emitters are VCI shaped like a cartridge, so one goes in the chamber, a magazine or the bore with no rigging. They come in 9mm, .45 ACP, 5.56/.223, 7.62/.308 and 12 gauge, in 2 and 3 packs. One per gun is plenty in a closed case or a gun sock. In an open safe they mostly help the guns nearest to them, so spread them out. Full write-up in the VaporTack SilentDry review.

Step 4: Wipe it down before it goes away

Fingerprints are salt water. The sweat you leave on a receiver after a range day will etch through bluing in a humid safe. So the last thing that touches the gun before storage should be a cloth with a light oil on it.

The Silent Dry Anti-Rust Wipes come pre-soaked with VCI oil, so one wipe cleans and leaves the protective film in a single pass. For the bore and the bits a cloth cannot reach, the Anti-Rust Oil Pen is a felt tip full of the same oil. Keep the oil off wood stocks. It darkens and softens them over time.

Step 5: Never store a cold gun

This is the one most people skip. After a cold hunt, leave the rifle out of the safe with the case open for a few hours. Let it come up to room temperature, then wipe off the condensation and put it away. A bit of patience saves you a re-blue.

The short version: how to keep guns from rusting

  • Hygrometer in the safe. Aim for 30 to 50 percent.
  • A renewable dehumidifier sized to the safe. Recharge it when it says so.
  • VCI emitter in each gun you care about, or at least in each case.
  • Oiled wipe-down before storage, every time.
  • Let cold guns warm up before they go in.

Common questions

Will my guns rust in a fireproof safe?

Yes, and often faster than in a plain steel cabinet, because the fireboard lining holds moisture. Fireproof safes need a dehumidifier more than any other kind.

How often do I recharge the Hypercube?

Depends on the room. In a dry house, maybe every couple of months. In a wet basement in spring, every few weeks. The hygrometer tells you, so you do not have to guess.

Is VCI safe around ammunition and scopes?

Yes. It is made for enclosed storage with everything in it, including ammo, optics and electronics. It leaves nothing on the surface that you need to clean off before shooting.

Is a dehumidifier enough on its own?

For most safes in most houses, yes. Add VCI and an oiled wipe-down if the safe is in a basement or garage, or if you own anything with a nice blued finish.

Where to get it

Everything above is in the Silent Dry section. For a typical safe, the starter setup is one Hypercube, a pack of VaporTack in your main calibre and the wipes. That is around $100 and it covers the whole safe for years.

Related Posts