Surface rust is normal and fixable. Pitting is not. The trick to remove rust from a gun is knowing which one you are looking at, working slowly, and stopping before you take the finish off with the rust. This works on blued and parkerized steel. Stainless is easier and the same method applies.
Before you start
Unload it. Check the chamber. Take the bolt out or lock the action open. Work somewhere with good light, because the whole job is about seeing when to stop.
Step 1: Figure out how bad it is
Light orange haze or small freckles that sit on top of the finish: surface rust. Ten minutes of work.
Rough brown crust that catches a fingernail, or dark spots that stay after the rust is gone: it has started to pit. You can stop it getting worse, but the marks are permanent.
Rust inside the action, on springs, or on a screw that will not turn: that is a gunsmith job, not a kitchen table job.
Step 2: Oil it first
Put gun oil or a VCI oil on the rusted area and let it sit ten minutes. The oil gets under the rust and loosens it, and it lubricates whatever you rub with so the finish underneath is not scratched. Never work on dry steel.
Step 3: 0000 steel wool, light pressure
Take a small pad of 0000 (four-aught) steel wool, wet it with oil, and rub the spot in small circles with about the pressure you would use to wipe a fingerprint off a phone. Rust is softer than the steel and the bluing under it, so it comes off first. Wipe, look, repeat. Stop the moment the orange is gone.
Bronze wool does the same job and cannot leave steel fibres behind. A copper coin, edge on, works for a single spot: copper is softer than the finish and harder than the rust.
Step 4: The bore
Bronze brush and solvent, then patches until clean. If the patches come out orange, keep going. If the bore looks frosted or has dark speckles after cleaning, it has pitted. It will still shoot, usually fine, but foul faster. A gunsmith can tell you if it is worth worrying about.
Step 5: Touch it up, if you want
Where surface rust came off, the bluing is often thinner or gone, leaving a grey patch. Cold blue from a bottle will darken it enough to hide. Degrease the spot first, apply, rinse, oil. It is cosmetic and it will never match a factory finish, but it beats a bare patch.
Step 6: Protect it and fix the cause
Wipe the whole gun with an oil that leaves a film. The Silent Dry anti-rust wipes are pre-soaked with VCI oil, one pass and it is done. The oil pen gets the bolt face, the chamber and the bits a cloth misses.
Then ask why it rusted. Nine times out of ten the answer is the safe. Put a dehumidifier in it, a VCI emitter with the gun, and check the humidity. Otherwise you will be doing this again in the spring.
What not to use
- Vinegar, CLR, naval jelly. They strip bluing along with the rust. You end up with bare grey steel.
- Sandpaper, wire wheels, Dremels. Instant scratches and a ruined finish.
- Coarse steel wool. Only 0000. Anything coarser cuts the bluing.
- WD-40 as a storage oil. Fine for loosening rust, but it evaporates and leaves nothing behind. Use a real gun oil or VCI oil for the last wipe.
When to give up and see a gunsmith
Deep pits on the barrel, rust in the trigger group, a seized screw, or any rust on a gun with collector value. A gunsmith can strip and re-blue the whole thing, which costs money but looks right. Grinding on it yourself lowers the value more than the rust did.
Common questions
Can I remove rust from a gun with a penny?
Yes, if it is actually copper. Older Canadian pennies are; the last ones were plated steel and will scratch. Any piece of copper works the same way.
Will steel wool scratch bluing?
0000 with oil and light pressure, no. Coarser grades or dry, yes.
Does rust come back?
Only if the storage does not change. Fix the humidity and it stays gone. The full storage routine is in the Silent Dry section.