Information & Education, Range Training

How to Clean Cosmoline Off an SKS (and Keep It Rust-Free After)

Historical photo of a soldier in a greatcoat resting beside an SKS rifle

Every surplus SKS comes packed in cosmoline, a waxy grease that kept the rifle rust-free in a crate for sixty years. It did its job. Now it will gum up the action, weep out of the stock every summer, and in one spot it can make the rifle unsafe. Full SKS cosmoline removal takes an afternoon. Here is how to do it and what to do the moment the steel is bare.

Why you cannot skip the bolt

The SKS firing pin is free-floating. There is no spring holding it back. If cosmoline in the bolt holds the pin forward, the rifle can fire when the bolt slams home, and it can keep firing until the magazine is empty. This is the well-known SKS slam fire, and cosmoline is the usual cause. So whatever else you do, the bolt comes fully apart and the firing pin channel gets cleaned until the pin rattles freely.

What you need

  • Mineral spirits or kerosene, a couple of litres, and a tub big enough for the barrelled action
  • Nitrile gloves, rags, an old toothbrush, a nylon brush
  • Hot water and dish soap
  • A hair dryer or heat gun, or a sunny day
  • A punch and small hammer for the firing pin retaining pin
  • Gun oil and anti-rust wipes for after

Work outside or in a garage with the door open. Mineral spirits fumes are not something you want in the kitchen.

Step 1: Strip it

Take off the gas tube and handguard, pull the bolt carrier and bolt, drop the trigger group, and take the barrelled action out of the stock. If you have not done it before, the SKS guide covers what the rifle is and the takedown order. Keep the small parts in a container so nothing walks away.

Step 2: Soak the metal

Everything steel goes into the mineral spirits: barrelled action, bolt carrier, bolt, trigger group, gas tube, piston, magazine. Let it sit an hour, then scrub with the brushes. The trigger group is the worst for hidden cosmoline, so work the brush into it from every side. Pull the parts, wipe, and do a second short soak in fresh spirits. When a clean rag stays clean, you are done.

Step 3: The bolt, properly

Drive out the firing pin retaining pin, slide the firing pin out, and clean the channel with a pipe cleaner or a patch on a rod until it comes out white. Reassemble, then the test: hold the bolt and shake it. You should hear the firing pin clicking back and forth. If it does not rattle, it is not clean. Do not fire the rifle until it does.

Step 4: The stock

Cosmoline soaks into the wood, and no soak gets it all out. What works: heat. A hair dryer or a heat gun on low, or a hot afternoon in the sun, makes the stock sweat grease to the surface. Wipe it off, heat again, repeat until it stops. A rag damp with mineral spirits takes the last film off. Do not soak wood in solvent or water. Some people leave the stock alone and just live with a bit of weeping in July. Your call.

Step 5: Bore and gas system

The bore is usually full of cosmoline too. Solvent, bronze brush, patches until clean. Then the gas tube and piston, which will be black inside from carbon on top of the grease. Scrub them, wipe them, and leave them dry: no oil in the gas system.

Step 6: Reassemble and function check

Put it back together and, with the rifle empty, check that the safety blocks the trigger, the trigger resets, the bolt locks back on an empty magazine, and the firing pin still rattles. Then it is ready for the range.

Step 7: It is bare steel now. Protect it.

This is the part most SKS guides skip. The cosmoline was the rust protection. You just removed it, and the steel underneath is unfinished in places, especially inside the receiver and under the stock. A stripped SKS in a damp safe will rust faster than any modern rifle you own.

  • Wipe every metal surface with a VCI oil. The Silent Dry wipes do it in one pass, and the oil pen gets inside the receiver and around the gas block.
  • Put a dehumidifier in the safe. Basements in Canada run 60 to 70 percent humidity for half the year and the SKS will find every bit of it.
  • Put a VaporTack VCI emitter in the case or the safe with it. There is no 7.62×39 size yet, so use the 7.62/.308 one next to the rifle rather than in the chamber. Full write-up in the VaporTack SilentDry review.

One more thing about surplus ammo

If you shoot surplus 7.62×39, assume the primers are corrosive. Run hot soapy water through the bore and the gas system the same day, then dry and oil. Corrosive salts plus a stripped SKS plus a damp safe is a bore ruined in a week. Commercial ammo like the Norinco 7.62×39 we sell does not have this problem.

Storage gear is in the Silent Dry section. SKS parts, magazines and stripper clips are in the SKS listings.

Related Posts